Blog RGB
Tout sur l’automatisation industrielle, la maintenance des flottes et la technologie de réparation. Actualités du secteur, produits recommandés, fabricants leaders et développements dans le domaine du RGB, le tout en un seul endroit. Nous sommes heureux de partager notre expertise en matière d’ingénierie, les opinions des techniciens et des spécialistes de l’équipement RGB. Nous vous encourageons à naviguer et à télécharger des documents.
Recherche de codes d'erreur
| Code d'erreur | Producteur | Catégorie d'équipement | Description |
|---|---|---|---|
| 402501 | Siemens | Simodrive 611 |
Impermissible BAG no. parameter in FC 25 |
| 402502 | Siemens | Simodrive 611 |
Impermissible channel no. parameter in FC 25 |
| 4026 | Siemens | Simodrive 611 |
Machine data %1[%2], link axis NC%3_AX%4 not used by any channel |
| 4027 | Siemens | Simodrive 611 |
Notice: MD %1 was also changed for the other axes of axis container %2 |
| 4028 | Siemens | Simodrive 611 |
Notice! The axial MDs of the axes of the axis containers were matched. |
| 4029 | Siemens | Simodrive 611 |
Notice: the axial MDs in axis container %1 will be matched on the next power-up |
| 403 | MECOS TRAXLER | IMC15 |
The control system did not detect correct current flow in the next output phase of the inverter |
| 4030 | Siemens | Simodrive 611 |
Channel %1 axis identifier missing in machine data %2[%3] |
| 4031 | Siemens | Simodrive 611 |
Channel %1 link axis %2 defined for more than one channel in machine data %3 |
| 4032 | Siemens | Simodrive 611 |
Channel %1 wrong identifier for facing axis in %2 |
| 4033 | Siemens | Simodrive 611 |
Notice: NCU link communication still not connected |
| 4034 | Siemens | Simodrive 611 |
Local link axis %1 is not allowed for different interpolation cycle time = %2/%3 |
| 4035 | Siemens | Simodrive 611 |
Interpolation cycle from NCU%1 = %2 does not match NCU%3 = %4 |
| 4036 | Siemens | Simodrive 611 |
Wrong NCU link configuration by MD %1 |
| 404 | Fanuc | Servo amplifier 400 alarms |
SERVO ALARM: n–TH AXIS VRDY ON – Even though the n–th axis (axis 1–8) READY signal (MCON) went off, the servo amplifier READY signal (DRDY) is still on. Or, when the power was turned on, DRDY went on even though MCON was off. Check that the servo interface module and servo amp are connected. |
| 4040 | Siemens | Simodrive 611 |
Channel %1 axis identifier %2 not consistent with machine data %3 |
| 4045 | Siemens | Simodrive 611 |
Channel %1 conflict between machine data %2 and machine data %3 |
| 405 | Fanuc | Servo amplifier 400 alarms |
SERVO ALARM: (ZERO POINT RETURN FAULT) – Position control system fault. Due to an NC or servo system fault in the reference position return, there is the possibility that reference position return could not be executed correctly. Try again from the manual reference position return. |
| 4050 | Siemens | Simodrive 611 |
NC code identifier %1 cannot be reconfigured to %2 |
| 4060 | Siemens | Simodrive 611 |
Standard machine data loaded |
Enquête de satisfaction
Nous vous serions reconnaissants de nous faire part de vos commentaires. Il ne vous faudra pas plus de cinq minutes pour répondre à l’enquête.
