Blog RGB
Tout sur l’automatisation industrielle, la maintenance des flottes et la technologie de réparation. Actualités du secteur, produits recommandés, fabricants leaders et développements dans le domaine du RGB, le tout en un seul endroit. Nous sommes heureux de partager notre expertise en matière d’ingénierie, les opinions des techniciens et des spécialistes de l’équipement RGB. Nous vous encourageons à naviguer et à télécharger des documents.
Recherche de codes d'erreur
| Code d'erreur | Producteur | Catégorie d'équipement | Description |
|---|---|---|---|
| 19 | Baumüller | Operating system P0202 |
Time slot – time error |
| 19 | Baumüller | Warnings power unit P0262 |
not used= 0 |
| 19 to 27 | Baumüller | Encoder 1 - serial interface P0234, encoder 2 - serial interface P0 235 |
reserved |
| 192 | Baumüller | Position controller P0213 |
Position deviation dynamic Adjustable |
| 193 | Baumüller | Position controller P0213 |
Position deviation static Adjustable |
| 194 | Baumüller | Position controller P0213 |
Encoder 1 is used for position control, but is inactive. This error is also shown, if the faulty positioning is in one of the inactive data records. |
| 195 | Baumüller | Position controller P0213 |
Encoder 2 is used for position control, but is inactive. This error is also shown, if the faulty positioning is in one of the inactive data records. |
| 196 | Baumüller | Position controller P0213 |
Software limit switch 1 exceeded |
| 197 | Baumüller | Position controller P0213 |
Software limit switch 2 exceeded |
| 198 | Baumüller | Position controller P0213 |
Hardware limit switch 1 exceeded |
| 199 | Baumüller | Position controller P0213 |
Hardware limit switch 2 exceeded |
| 2 | Baumüller | Encoder 1 - serial interface P0234, encoder 2 - serial interface P0 235 |
Error in internal angle offset |
| 2 | Baumüller | Finding notch position P0237 |
Plausibility step 1 • Method 0: Current is too low or shaft is too immovable or the direction of the rotating field P0087 is wrong. • Method 2: Tracking controller does not converge to a steady rotor position (the tracking controller should calculate the same value from different start values with unchanged rotor position). If the measures for troubleshooting could not assist, then the motor is possibly not qualified for the injection procedere (e.g. the magnetic anisotropism of the motor is not enough impressed, magnetic unbalance of the three phases, etc.) |
| 2 | Baumüller | Mains monitor P0236 |
Mains monitor has detected error Undervoltage mains |
| 2 | Baumüller | Module A to E P0240 to P0244 |
Recognized module not permitted at this position |
| 2 | Baumüller | Power supply P0261 |
Mains undervoltage |
| 2 | Baumüller | Procesor P0201 |
Incorrect or unexpected interrupt has occurred |
| 2 (dot) | Fanuc | Servo amplifier alarms |
+5 VDC of the control circuit power supply is abnormally low. |
| 20 | Fanuc | Servo amplifier SVPMI (6134, 6230) |
Excessive offset of the phase V current detection circuit |
| 20 | Baumüller | Operating system P0202 |
1 = No free memory |
Enquête de satisfaction
Nous vous serions reconnaissants de nous faire part de vos commentaires. Il ne vous faudra pas plus de cinq minutes pour répondre à l’enquête.
